Collection Search

Complete eel-weir stick. Both ends taper to a blunt point. The proximal end has wearing, with the outer layer of wood cracking away. There are fractures along the whole shaft.

Complete kahawai lure. Wooden shank with knobs at head and large knob at base. Paua shell inlay. Straight bone point with internal barb. Lashings and twisted cord at head and base.

Complete kahawai lure. Wooden shank with knobs at head and large knob at base. Paua shell inlay. Straight bone point with internal barb. Lashings at base and head with twisted cord at head.

Complete taiaha. Surface is worked smooth and polished. Human face carved on each side at the proximal end. Protruding tongue has a rauru (spiral and notch) pattern. Two eyes have paua shell inlays intact. Blade is narrow and rounded, with a large chip missing from the edge.

Complete taiaha. Roughly carved human faces on each side of the proximal end. Metal drawing pins in three of the four eyes (perforation visible where one is missing). Unfinished spiral incised markings on one side of protruding tongue. Dark dyed twisted piece of fibre tied around the centre of the blade.

Complete taiaha. Proximal end carved with human face in high relief on each side. Protruding tongue has a rauru (double spiral with notches) pattern. Blade is undecorated, flaring out to the distal edge, with a chip broken off one side.

Complete wahaika rakau. It has a perforation that is rectangular and has been chipped out. It has whakairo on both sides and the top of the head, and also on both sides of the body. It has a carved human figure below the handle with shell inlays for eyes. It is well polished.

Complete tatā (canoe bailer). Dark brown wood. Handle is straight and carved with a rauponga (ridge and notch) pattern and a face carving at the proximal end. Eyebrows, eyes (one with paua shell and one missing), nose and mouth indicated. Scoop is U-shaped with thick walls. Exterior surface is carved with faces and spirals around the rim and koru pattern on the bottom. The carvings on the scoop are amateur, possibly unauthentic and added after the handle carvings. The interior of the scoop is unornamented with a ridge at the pouring edge.

Complete wooden tatā (canoe bailer). There is a large curved handle with a simple manaia carved into the handle knob. Where the handle meets the bailer there is a large mouth carving. At the funnel end of the bailer there are two curved ridges. The walls of the bailer are high and straight. There are several cracks where the walls meet the base. Wood is stained dark red.

Complete taiaha. The arero (tongue) is decorated with rauponga style carving (rows alternating with notches) on both sides. The upoko (head) has two sets of inset eyes. One eye retains paua shell, the other three have red sealing wax remaining. The rau (nose) is rounded and bears marks of use.

Complete paddle. Handle oval in section and expands gently to blade. Proximal end has a long, diamond cross-sectioned knob that comes to a point. Sides of blade widen near the distal end, and then taper approximately 70cm from the end. Blade has longitudinal central ridge on front and back.

Complete kahawai lure. Curved wooden shank with notches at head and base. Muka lashings across notches and cord at head. Paua shell inlay. Bone point is complete and straight with internal barb. Orange and yellow feathers attached by lashings at the base.

Complete composite fishhook. Curved wooden shank with large bone point attached with muka lashings. Bone point is straight with and incurved tip and three external barbs and one internal barb. Lower external barb and internal barb have two notches on them. Additional muka lashings twisted around the head.

Complete teka (footrest) for a kō (digging stick). Single piece of mid brown wood, with step and base at a 90-degree angle from each other. Step is sawn flat at the top end and base tapers to the bottom end, with a chip missing from the edge. Base has a projection with a perforation for lashing. Surface is smooth with chisel marks evident.

Complete wooden patu (club). The head has a hole drilled through it, with a split originating from the hole. The handle is formed by a reduction of the head, with minor demarcation for a grip at the end of the handle. There is no ornamentation.

Complete fern root patu rakau. The handle is demarcated by a line and a reduction of the blade. The blade is worn at the tip, with surface cracks across the whole patu.

Complete hoe (waka paddle). Dark brown wood. Surface is worked smooth. Blade is roughly lenticular in cross section, with a flatter back than front. Relatively narrow blade, tapering to a point at the distal end. Perforation where the blade meets the handle. Handle is round in cross section. Large knob on the lower section of the handle, possibly from a natural knot in the wood. Another knob at the butt of the handle.

Complete wooden pūtōrino. Bound at each end with harakeke strands; discolouration on the surface appears to indicate that there once were additional binding sites. Single mouth perforation on one side with rudimentary eyes carved onto surface and very two shallow koru radiating from centre below mouth. An unevenly set cross-shaped mark sits on top face above eyes. Surface has been varnished in the past but now worn. Two cracks running longitudinally on both sides with tape residue running along one.

Complete wooden pūtōrino. Bound with strands of harakeke at each end and at four places on the body. Tapered at the distal end, with a knobbed mouthpiece at the proximal end. Perforation at the centre on one side. Surface has been painted mid-brown. Two cracks running longitudinally on each side.