Collection Search

Circular whale vertebra with four drilled holes. The upper hole has an irregular shape. The front face has residual bone remaining.

Complete pendant in adze shape. Surface is mostly smooth, with flaking around the proximal end. Cross-section is rectangular. At the proximal end there is a perforation. There is no shoulder. Bevel is continuous with blade. The cutting edge is sharp and curved.

Unfinished harpoon head with single barb and bifid base. Cross-section is oval. Missing perforation through centre, barb and tip unsharpened.

Incomplete bone comb, five vertical cut marks at the distal end indicating unfinished teeth. One additional cut mark is complete. Another cut mark runs horizontally above the others. Reduced on one side, with a rounded, grooved projection. Shape is trapezoidal, tapering toward the distal end. Concave cross section.

Broken whalebone heru (comb). It is missing two teeth and a portion of the proper left side. The proper left side of the comb has been worn in, potentially to accomodate an ornamental feature which has broken off. The proper left lateral margin has notches from the break to the top of the teeth. Six teeth remain. There is a crack originating at the top of the comb, along with some chipping.

Complete pounamu adze. Cross-section is lenticular. Surface is ground, with bruising on the poll. There is major differentiation of the butt, with a change in urface and a reduction of the sides. The bevel is demarcated by a curved ridge. The cutting edge is curved and sharp.

Unfinished hei tiki. There is a notched groove at the proximal end of the hei tiki. The pendant is roughly shaped with grooves at the neck, arms and legs. The grooves at the leg go through the pounamu.

Bone comb with seven prongs. Perforation drilled from both sides in one corner of the proximal end. Sawing marks at the proximal edge.

Complete tattoo chisel, carved tines at the distal edge.

Complete tooth pendant. The tooth curves to a blunt point. There is a large crack through the distal end of the pendant. The proximal end suspension hole has been drilled from both sides.

Complete adze. Cross-section is rectangular, front edges rounded on butt. The surface is mostly ground, small areas of bruising on back and entirety of the sides and front of butt. There are two lugs on the front proximal end of the adze. There is major differentiation between butt and blade, front and sides reduced forming shoulder. Bevel is a demarcated by a line at chin. The cutting edge is unusually wide, sharp and curved, with light chips along cutting edge.

Complete tewhatewha. The upper edge of the blade is curved, with a slight slope to it. The lower edge of the blade is curved, with a small perforation near the shaft. The cross-section of the upper shaft is lenticular, becoming circular on the lower. The surface of the tewhatewha is fully carved. The blade has a rauru spiral on either side, with partial spirals filling in gaps around the edges. The shaft of the tewhatewha is carved with three haehae followed by a row of pakati in a variety of patterns; alternating linear then curved as it goes down the tewhatewha. Approximately 40cm from the bottom of the tewhatewha there is a carved face with missing paua shell inlay.

Complete tokotoko. The distal portion of the tokotoko is uncarved. Everything above 34cm is finely carved in a variety of patterns. After a section of mixed diagonal and longitudinal carved lines, there are stacked human figures. The lowest two are bilateral carved faces with notched paua shell inlay eyes. The figure at the proximal end is a full standing human figure with two slender legs, ending with carved buttocks and stomach with four fingered hands that meet on the stomach. The arms and chest are carved, as is the face. The eyes are inlaid with notched paua shell. There is a curved handle protruding from the back of the head that curves around and meets the tokotoko again at the back of the shoulders of the figure. There is a final human face here where the handle meets the shoulders that also has inlaid paua shell eyes and long carved lip.

Complete kahawai lure. Curved wooden shank with knob at base for lashings. Iridescent paua shell inlay. Muka lashings at head and base. Twisted muka cord attached at head. Straight bone point with very prominent internal barb.