Collection Search

Bone comb with seven prongs. Perforation drilled from both sides in one corner of the proximal end. Sawing marks at the proximal edge.

Complete curved fishhook point.

Complete tattoo chisel, carved tines at the distal edge.

Complete needle. Distal end is sharp and curved. There is a drilled, circular eye at the proximal end.

Complete bone pendant. Straight with suspension hole at the proximal end, coming to a point at the distal end.

Unfinished needle. Distal end is sharp. There is a drill mark on one side of the proximal end, an eye partly bored.

Broken adze (all but cutting edge remaining) Cross-section is oval. Surface is ground, except on broken edges. Undifferentiated between butt and blade. Though sides taper towards poll. Bevel continuous with blade. Cutting edge broken off.

Complete roughout Cross-section is trapezoidal, with back narrower than front. Surface is flaked. Undifferentiated between butt and blade. Though sides taper to a point at poll end. Back slopes up to meet poll Bevel and cutting edge unfinished. Cutting edge as is blunt and straight.

Complete tewhatewha. The upper edge of the blade is curved, with a slight slope to it. The lower edge of the blade is curved, with a small perforation near the shaft. The cross-section of the upper shaft is lenticular, becoming circular on the lower. The surface of the tewhatewha is fully carved. The blade has a rauru spiral on either side, with partial spirals filling in gaps around the edges. The shaft of the tewhatewha is carved with three haehae followed by a row of pakati in a variety of patterns; alternating linear then curved as it goes down the tewhatewha. Approximately 40cm from the bottom of the tewhatewha there is a carved face with missing paua shell inlay.

Complete huata or tao (spear). Wooden rod with a smooth, undecorated surface. Tapers to a blunt point at one end and a flattened, bevelled edge on the other end. Carved inscription "NA MANAMA" near the blunt end.

Complete timo (grubber). Made from a single piece of light brown wood, worked to about a 45-degree angled curve. Surface is smooth and polished. Butt of the handle has a ngututa head carved, with double ngututa heads on the exterior edge where the handle meets the blade. Eyes have paua shell inserts. Previously broken at the top of the blade and repaired. Tapered to a blunt point on the distal end.

Complete adze. Cross-section is oval. Surface of lower blade ground, becoming more flaked towards butt. Minor differentiation between butt and blade. Front reduced, but rises again at mid-butt. Back and front of upper butt has been shaped to point at the poll Bevel is continuous with blade. Cutting edge is sharp and curved.

Broken adze (blade remaining). Cross-section is semi-circular, back flattened. Surface is ground. Butt not present. Undifferentiated until broken point. Bevel is continuous with blade. Cutting edge is sharp and curved.

Ceremonial adze haft, identified as a fake. Dark brown wood with paua shell inlay and a twisted muka cord for lashing. Handle is carved with a geometric pattern of ridges and notches, with a human head carved on the butt. Haft consists of a carved human figure with adze housing situated between rear of legs, grasping a fish to its mouth with both three-fingered hands. Manaia eyes and forehead runs down ridge to base of hafting point. Figures are carved with geometric patterns.

Complete hafted adze Cross-section is rectangular. Adze has a smooth, metal surface, though very rusted. Undifferentiated between butt and blade, though sides taper towards poll Bevel continuous with blade. Cutting edge is sharp and curved. Hafted adze. Adze is connected to shaped haft of dark wood, with twine.

Pair of wooden weaving sticks with sample of twined flax fibre tied between them. The sticks are not identical. One (a) is circular in section, the other (b) slightly oval. Both taper to a point at distal end, stick (a) broken on tip and has grey/brown substance on it. Proximal end is flat. Stick (b) appears to have been chewed and broken. Each has 30mm wide groove, 35mm below end, around, to which is attached the weaving. Coarse muka with 22 rows of double pair twining plus an insert row and commencement row. Commencement and final row have scalloped weft introduced and short pieces of black flax fibre forming decoration.

Pair of wooden weaving sticks with sample of twined flax fibre tied between them. Both weaving sticks taper to a point at distal end, with a groove at the proximal end to which is attached the weaving. One of the sticks is broken at the proximal end. Coarse muka with 8 rows of double pair twining plus an insert row and commencement row. Commencement row has scalloped weft introduced and short pieces of black flax fibre forming decoration.

Complete kahawai lure. Curved wooden shank with notches at head. Shell inlay. Straight bone point with internal barb. Muka lashings at head and base.

Complete kahawai lure. Wooden shank with paua shell inlay. Straight bone point with internal barb. Muka lashings at base and head.

Complete kahawai lure. Curved wooden shank with knob at base for lashings. Iridescent paua shell inlay. Muka lashings at head and base. Twisted muka cord attached at head. Straight bone point with very prominent internal barb.