Collection Search

Complete adze. Brown stone. Asymmetrical trapezoidal cross-section at blade, rounded rectangle at butt. The surface is roughly flaked and bruised apart from smooth areas on the bevel and front of the blade. There is no distinction between the blade and the butt. The bevel is only distinguished from the blade by its partially smooth surface. The cutting edge is straight and sharp with one chip.

Complete adze. Light brown stone. The cross-section is rectangular. The surface is roughly flaked with ground areas on the bevel and the front of the blade. There is no distinction between the blade and the butt. The bevel is flat and distinguished from the blade by the smooth surface. The cutting edge is straight and sharp with some small chips.

Complete adze. Light grey stone. The cross-section is trapezoidal with the back narrower than the front. The surface is smooth with bruising on the sides and on the front of the butt. There are flake scars on the poll and on the back of the adze. The butt is distinguished from the blade by a slight reduction on the proper left front, and by the change in surface from smooth of the blade to bruised. The bevel is demarcated from the blade by a raised chin. The cutting edge is asymmetrical and sharp. "Otago" is written in pencil on the front.

Complete adze. Irregular trapezoidal cross-section. The stone is light brown. The surface is roughly flaked with smooth areas on the front of the blade. There is no differentiation between the butt and the blade. The bevel is asymmetrical and concave, and the cutting edge is straight and sharp.

Complete two-mouthed hinaki (eel trap). Two-strand, half-twisted twining made from vine. Stick-like projections at the end of the eel funnels. Four internal braces woven into body. Bait door at one end with two rounded handles. Another larger handle on the other side.

Complete hue (gourd container or calabash). Mid brown and mid orange. Elongated, bulbous base with a short, curved neck. Top of the neck has been cut away and the edges have been polished smoothed. Small perforation just below the top. Base is severely cracked.

Complete hue (gourd container). Dark orange in colour. Hole cut out on one side of neck; small piece of stem still attached. A twisted and knotted piece of muka cord is looped around the body of the gourd and tied at the top for use as a carrier.

Complete hue or taha tuatua (gourd container or calabash) inside a woven kete. Oval shape, with a rounded base broken in several fragments. Top is cut off at the neck, creating a large circular hole with sides worked smooth. Kete is made of unscraped harakeke, plaited in an over-one, under-one twill, broken in several places and with a broken muka handle. Metal ring and broken pieces in plastic bags accompany the hue.

Complete tatā (canoe bailer). Dark brown wood. Handle is straight and carved with a rauponga (ridge and notch) pattern and a face carving at the proximal end. Eyebrows, eyes (one with paua shell and one missing), nose and mouth indicated. Scoop is U-shaped with thick walls. Exterior surface is carved with faces and spirals around the rim and koru pattern on the bottom. The carvings on the scoop are amateur, possibly unauthentic and added after the handle carvings. The interior of the scoop is unornamented with a ridge at the pouring edge.

Complete kahu huruhuru (fowl and kiwi feather cloak). There are kiwi feathers along the borders mixed with fowl feathers. There are reddish fowl feathers and white fowl feathers with iridescent black fowl feathers tags that form vertical parallel lines. Along the bottom edges there is black and natural twine fringing. The top of the cloak is worked in a thick multi-strand braid with two ties approximately 25cm from the edges. The cloak is wider at the top, narrowing towards the lower edge.

Kete Muka woven from natural and black dyed muka (flax fiber) using whatu aho patahi (single-pair weft-twining). Cast on for this kete is unusual as is appears a base cord has been used as a foundation, whenu (warp strands) have been added by creating a loop with the whenu and pulling both tail ends through. The body of this kete is decorated with mawhitiwhiti (woven cross stitch) patterns. A badly deteriorating natural and black muka three ply whiri (braid) has been added to act as a handle. Frill work woven outer edge in black and natural muka.

Complete tatā (canoe bailer) made of a split whalebone. Large bulbous end made from the epiphysis of the bone, tapering to a straight, open pouring edge. Exterior side of the epiphysis has a mouth and protruding tongue carving and decorative geometric patterns. Handle curved over the top, with a human face (spiral eyes, nose, lips and tongue) indicated at the end. Surface has been polished on one side, and is burnt on the epiphysis and on the handle. Holes at the epiphysis. Has previously been broken and repaired at the pouring edge. Identified as a fake, not of authentic Māori origin.

Complete hue (gourd container or calabash) with bulbous base and relatively small, narrow neck. Single, square perforation at base of neck and remnant of vine stem at the top. Fibre cord twisted and knotted around gourd (dividing body into 8 areas) with the three individual cords held together above the neck. Rattles.

Complete adze. Cross-section is rectangular, with rounded corners. Surface of lower blade and bevel is ground. Flaked on all other surfaces. Undifferentiated between butt and blade. Front slopes slightly towards poll, and large chip on back of poll. Bevel is demarcated by a line, and where surface changes from flaked to ground. Cutting edge is sharp and straight.

Broken bone comb, head was previously broken in two pieces and glued back together; all ten teeth are broken off. Proximal edge is oblique, sides are straight with sawing marks evident on one side edge.

Broken bone comb. Previously broken in several pieces and glued back together; large part of head, centre portion, and various teeth are missing. Proximal end is rounded. A rounded projection on one side edge has broken off. 26 teeth, all broken at various points. Surface is in poor condition, possibly varnished and covered in glue, with pieces of index card attached to one side.

Broken bone comb, head remaining. Rounded at the proximal end. A carved head is projecting off one side edge; mouth, tongue, and eye are indicated. Remnants of about 25 teeth, with more likely, all broken off at the base of the head.

Broken bone comb, head remaining. Proximal edge is rounded, with a projection coming off one side. Projection is worn with two perforations, possibly indicating a bird or taniwha head. Large piece chipped off below projection. Other side edge is straight with a sawing mark. Evidence of 17 teeth, all broken close to the base of the head.

Complete adze Cross-section is oval, with narrow end to front. Surface is ground. Undifferentiated between butt and blade. Sides tapered towards poll. Bevel is continuous with blade. Cutting edge comes to fine point rather than a traditional edge.

Complete adze Cross-section of blade is rectangular. Cross-section of butt is oval. Surface is ground on blade front and back and sides, bruised on butt front, flaked on back sides and back of butt. Minor differentiation between butt and blade. Sides reduced. Bevel is continuous with blade, and slightly concaved. Cutting edge is sharp and curved.